Essential Plumber Tips for Installing a Bathtub
Essential Plumber Tips for Installing a Bathtub
Blog Article
They are making a number of great observations on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this post underneath.
Installing a bath tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old tub is conveniently easily accessible, the task can move easily; if you need to open up a wall to remove the old tub and also place the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the work as well as fit attempting it. As opposed to hiring a service provider to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you might require a specialist plumber to make tube connections.
This short article will aid you mount a brand-new bath tub in your shower room if you have currently gotten a brand-new tub and also don't need to change the arrangement of your previous water pipelines.
Your devices and product checklist should consist of the following:
Preparing for the Installment
To start with, the sustaining frame provided with the bathroom needs to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of removing the existing faucets can be fairly troublesome as a result of the limited gain access to that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been removed, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before going on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the bathtub until the level reviews level.
To install faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the other faucet.
Turn on the supply of water and also inspect all joints and also new pipework for leakages as well as tighten them if needed. Fill the bath tub as well as additionally examine the overflow outlet and also the normal outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub needs to wait until the tub has actually been made use of at the very least once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washers are in place in between the faucet and the sink. Safeguard the tap in position with the supplier provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind ought to be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to split a stiff seal, triggering the water to permeate the wall in between the bath as well as the tiling, bring about difficulties with moisture as well as possible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealant can crack relatively early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that article on Tools You Need to Install a New Bathtub when doing research the search engines. If you enjoyed our blog entry please remember to pass it around. We treasure reading our article about How to Install a Bathtub Yourself.
Pricing Report this page